Heat pump guide: which air-to-water heat pump is right for you?

Guide · Heat pumps

An air-to-water heat pump draws the heat for heating and hot water from the outside air. To run reliably and economically in winter, its output, flow temperature and power connection must match the house.

Here you will learn how a heat pump works, what matters when sizing it, what R290 means and which heat pump from our shop suits your house.

All heat pumpsGo straight to the model comparison ↓

The key points in brief

Heating load firstThe right size is determined by the building's heating load, not by the living area alone. Too large is just as unfavourable as too small.
Low flow temperature saves electricityThe lower the flow temperature, the more efficiently the heat pump works. Underfloor heating and large radiators are ideal.
Monoblock with R290All heat pumps in our shop are monoblock units with the natural refrigerant R290. Only water pipes lead into the house.
Strong with PVWith solar power from your own roof, heating and hot water can be partly self-supplied. A battery helps in the evening.

How an air-to-water heat pump works

A fan draws in outside air. In the heat exchanger, the refrigerant evaporates even at very low temperatures, absorbing heat from the air. A compressor raises the gaseous refrigerant to a higher pressure and temperature level. In the second heat exchanger, it transfers this heat to the heating water. The refrigerant then expands and the cycle begins again.

The heat pump needs electricity mainly for the compressor, fan and pump. The larger part of the heat is supplied by the ambient air. How much heat is produced from one kilowatt hour of electricity is shown by the COP (coefficient of performance at a fixed operating point, e.g. A7/W35: 7 °C air, 35 °C flow). In real operation over the whole year, what counts is the seasonal performance factor – it depends heavily on the building, heating surfaces and settings.

Heating, hot water and coolingThe heat pumps in our shop heat, prepare hot water via a suitable storage tank and, according to the manufacturer, can also actively cool. Cooling via floor or wall requires dew point monitoring so that no condensation forms.

Monoblock or split?

Monoblock Split
Design The complete refrigerant circuit is in the outdoor unit. Only heating water pipes lead into the house. Outdoor unit and indoor unit, connected via refrigerant lines.
Installation Hydraulic connection by the heating installer, no on-site intervention in the refrigerant circuit. Laying, testing and filling refrigerant lines – only by a certified refrigeration specialist.
Frost protection The water pipes to the outside must be protected against frost. Only refrigerant outdoors, no water.
In our shop all Midea M-Thermal Arctic and Nature currently no split heat pump

The Midea units have an integrated electric heater, which the manufacturer describes as a backup and frost protection heater.

Sizing: heating load and output

The basis of any planning is the heating load: the heat output the house needs on the coldest design day. A specialist planner or energy consultant calculates it room by room according to the applicable standard. Rough rules of thumb per square metre do not replace this calculation, because insulation, windows, ventilation and location make a big difference.

Important when comparing: the rated output in the datasheet applies to mild conditions (A7/W35). In frost, the output drops. That is why our table also shows the values at −7 °C outside temperature (A−7/W35). The heat pump should cover the heating load at the design point without the electric heater if possible; a surcharge is added for hot water preparation.

Too smallThe electric heater kicks in frequently. This costs a lot of electricity.
Too largeThe heat pump often cycles on and off in the transitional season. This reduces efficiency and puts strain on the compressor.
Just rightThe heat pump modulates for long periods and evenly – this is how it achieves the best seasonal performance factor.

Flow temperature: the most important efficiency lever

The flow temperature is the temperature at which the heating water flows to the heating surfaces. The smaller the difference between outside air and flow, the less the compressor has to work. That is why underfloor heating at around 35 °C is ideal. With large radiators, the heat pump also works well in existing buildings.

According to the manufacturer, the heat pumps in our shop reach flow temperatures of up to 75 °C (Arctic) or 80 °C (Nature). This helps with old radiators and hot water. For economical operation, however, the flow temperature should be kept as low as possible. Hydraulic balancing and a well-adjusted heating curve often achieve more than a larger unit.

Efficiency class at 35 °C and 55 °CThe energy efficiency class for space heating is given for low temperature (35 °C) and medium temperature (55 °C). The Arctic series has A+++ at 35 °C and A++ at 55 °C, the Nature series A+++ at both temperatures.

Refrigerant: what R290 means

R290 is propane – a natural refrigerant with a very low global warming potential. It is well suited to high flow temperatures and is therefore also interesting for renovations. All Midea heat pumps in our shop work with R290; the filling quantities are 0.7 to 1.5 kg depending on the model.

Because R290 is flammable, the manufacturer prescribes protection zones and clearances around the outdoor unit – for example to windows, light wells and basement stairs. The specialist company should check these requirements from the installation instructions when choosing the installation location. Air conditioners often use R32 in addition to R290; more on this in the air conditioning guide.

Heat pumps compared

Model Power connection Heating output / COP at A7/W35 Heating output at A−7/W35 max. flow Sound power
Arctic 6.5 kW 1-phase, 230 V 6.2 kW / 4.90 5.9 kW 75 °C 58 dB(A)
Arctic 8.4 kW 1-phase, 230 V 8.4 kW / 5.00 7.0 kW 75 °C 60 dB(A)
Arctic 10 kW 1-phase, 230 V 10.0 kW / 4.70 8.0 kW 75 °C 61 dB(A)
Arctic 12 kW 3-phase, 400 V 12.0 kW / 4.80 10.0 kW 75 °C 65 dB(A)
Arctic 14 kW 3-phase, 400 V 14.0 kW / 4.50 11.5 kW 75 °C 65 dB(A)
Nature 8.3 kW 3-phase, 400 V 8.0 kW / 5.25 7.0 kW 80 °C 53 dB(A)
Nature 10 kW 3-phase, 400 V 9.5 kW / 4.95 8.0 kW 80 °C 54 dB(A)
Nature 12 kW 3-phase, 400 V 12.1 kW / 4.95 10.0 kW 80 °C 55 dB(A)
Nature 14 kW 3-phase, 400 V 14.0 kW / 4.70 12.0 kW 80 °C 57 dB(A)

All models: monoblock, refrigerant R290, heating operation down to −25 °C outside temperature, heating and cooling. Sound power as ErP sound power level. Integrated electric heater: 3 kW for Arctic 6.5 to 10 kW, 9 kW for Arctic 12 and 14 kW and for all Nature models. Further values can be found in the datasheet on the respective product page.

M-Thermal Arctic M-Thermal Nature
Outputs in our shop 6.5 · 8.4 · 10 · 12 · 14 kW 8.3 · 10 · 12 · 14 kW
Space heating efficiency class A+++ (35 °C) / A++ (55 °C) A+++ (35 °C) / A+++ (55 °C)
max. flow temperature 75 °C 80 °C
Power connection 6.5 to 10 kW single-phase, 12 and 14 kW three-phase all models three-phase
Dimensions (W × H × D) 6.5 kW: 1,299 × 717 × 426 mm; 8.4 to 14 kW: 1,385 × 865 × 523 mm 1,330 × 1,051 × 475 mm
Weight 95 to 137 kg 153 to 169 kg
Strengths compact, single-phase models for houses without three-phase power at the installation location quieter, higher efficiency at 55 °C, for renovations with higher flow temperature

Decision guide: you want … → choose …

A well-insulated new build with underfloor heating and a low heating load.→ Arctic 6.5 kW→ Arctic 8.4 kW
A heat pump without a three-phase connection at the installation location.→ Arctic 8.4 kW→ Arctic 10 kW
A renovated existing house with radiators and higher flow temperature.→ Nature 10 kW→ Nature 12 kW
A particularly quiet unit, e.g. when close to the neighbours.→ Nature 8.3 kW→ Nature 10 kW
A larger house or two-family house with a higher heating load.→ Arctic 14 kW→ Nature 14 kW

Heat pump and photovoltaics

Heat pump and PV system complement each other well: the heat pump can convert solar power directly into heat and "park" it in the buffer tank, the hot water tank or the screed of the underfloor heating. Especially in spring, summer and autumn, a large part of the hot water can be generated with your own electricity. In winter the PV system supplies less – then grid supply remains important.

For the heat pump to use surpluses specifically, a control system is needed: an energy management system or a smart meter with a suitable interface. Midea specifies integration into energy management and smart home systems for the M-Thermal units. Which interface your energy manager uses should be clarified before purchase. A battery additionally shifts solar power into the evening.

VAT: 19%Heat pumps are not PV components. The zero tax rate for photovoltaics does not apply to them – they are sold with 19% VAT. What falls under the zero tax rate is explained in our guide 0% VAT on PV – what applies?

Funding

In Germany there are state funding programmes for installing a heat pump in an existing building. Amounts, bonuses and technical requirements change regularly. Programmes frequently require, among other things, installation by a specialist company, hydraulic balancing and minimum efficiency values. Often the application must be submitted before placing the order.

Therefore check the current conditions with the funding body or your energy consultant before purchasing – and clarify whether the desired unit and the planned installation meet the requirements.

The matching products

You can find all output levels under Heat pumps. Would you like to cool individual rooms or provide additional heating? Then read our air conditioning guide.

3 mistakes you should avoid

1. Buying by living areaWithout a heating load calculation, the heat pump quickly ends up too large or too small. Both cost efficiency.
2. Setting the flow temperature too highEvery degree less flow temperature saves electricity. Check the heating curve and hydraulic balancing after commissioning.
3. Planning the installation location too lateNoise, clearances to neighbours and the R290 protection zones determine the location – ideally before purchase.

Frequently asked questions

Does an air-to-water heat pump also work in an older building?

Yes, if the heating surfaces manage with a moderate flow temperature. Often a few larger radiators and hydraulic balancing are enough. With A+++ at 55 °C and up to 80 °C flow, the Nature series is designed for renovations.

What output do I need?

Only the heating load calculation for your building can tell you. When comparing, look at the heating output at low outside temperatures (e.g. A−7/W35), not just the rated output.

Do I need a three-phase connection?

The Arctic models with 6.5, 8.4 and 10 kW are connected single-phase at 230 V. Arctic 12 and 14 kW and all Nature models require a three-phase connection.

Who may install a monoblock heat pump?

The hydraulic and electrical connection is a job for a specialist company. Because the refrigerant circuit is sealed at the factory, no work on the refrigerant is required on site. A specialist company is usually a prerequisite for funding programmes.

Can the heat pump cool in summer?

Yes, according to the manufacturer, the Midea units in our shop can actively cool. Cooling via floor or wall requires dew point monitoring. For individual rooms, a split air conditioner is often the simpler solution.

How loud is a heat pump?

The datasheet states the sound power level of the outdoor unit – 53 to 65 dB(A) for the models in our shop. How loud it is at the neighbour's depends on distance and installation location. Both series have a silent mode.

Are the heat pumps available with 0% VAT?

No. Heat pumps do not fall under the zero tax rate for PV systems and are sold with 19% VAT.

Is a heat pump with a PV system worthwhile?

Usually yes, because hot water and the transitional season in particular can be covered well with solar power. How much depends on PV size, battery and control.

Your heat pump – properly sized

You can get air-to-water heat pumps in various output levels from us, plus PV systems and batteries. Send us your heating load, heating surfaces and power connection – we will help you choose.

Note: This guide does not replace planning by a specialist company. Check heating load, installation location, noise protection and funding conditions before purchase using the manufacturer's current documentation and requirements.

All information without guarantee. Subject to technical changes and errors. The current manufacturer documentation is authoritative.

Back to blog